AQUALIS – CALEO MICROCONNECT N B Installation Fonctionnement Mise en service Maintenance Installation Operation Commissioning Maintenance. Aqualis Caleo. 60H. 60HT. 70HT. Heating capacity *. kW. Power input *. kW. COP. Refrigerant fluid RC – Load. CIA. T CALEO. 10 – NA E. Instruction manual . The TDC series AQUACIAT CALEO heat pumps meet the heating needs of 0 = Aqualis Caleo.
|Country:||Central African Republic|
|Published (Last):||13 January 2018|
|PDF File Size:||17.14 Mb|
|ePub File Size:||13.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
To do so, simply loosen the nut measure on the bottom of the pressure switch approx.
Table of Contents Important Safeguards L If you have a radiant floor heating system, only use pressurised neutral gas compressed air, nitrogen to blow out the water remaining in the water loops. This contact terminal block J1 – terminals 1 and 5 remains closed once the outdoor temperature drops below the value of P9 or a fault occurs on the heat pump. Italiano 4 Location of the unit The installer must check the following points before handling, placing or connecting the unit: Heat pump and boiler operating ranges: Volkswagen New Beetle 2.
These settings identified by the letter P followed by a digit will help you to keep your unit operating at peak performance.
Page 10 5 Troubleshooting Page More information. The valve does not need to be separated from the heater by a shut-off valve.
Air/water heat pump – AQUALIS R series – CIAT
Washing the system with a suitable cleaner is recommended the type of cleaner depends on the system s materials. In addition there is a 2 year parts warranty on the compressor. Determine the right speed for the circulator based on the system s pressure losses and the available pressure curves for the heat pump. Heating is maintained until qaualis frost protection setpoint is reached.
Caldo Electric Boiler, kw is delivered More information. This can be done by opening the manual bleed valve located under the unit cover when turning the unit on or by installing a section of the water line and an automatic bleed valve over the unit.
The terminal also works as a room thermostat and thus plays an active role in controlling the unit. Failure to follow the safety rules and other basic safety precautions may result in serious More information.
English Installation D e u t s ch – Settings stored in memory for two hours following a power cut – Blue backlit digital display – Maximum dimensions: To keep your system running smoothly and, more specifically, if your Aqualis Caleo is installed at a high point, you must bleed the air contained inside it at the time of commissioning.
Always top up with the same type of mix initially used. The complete table of settings is given on the following page. If you have a radiant floor heating system, only use pressurised neutral gas compressed air, nitrogen to blow out the water remaining in the water loops. A 3 bar safety valve must be placed on the water loop. Although it is rain resistant, it may be installed under a shelter with adequate ventilation on all four sides.
Always dilute the antifreeze with water before adding it to the system. Connection – Attach the two wires to the terminal Fig. Adjusting setting P6 P6 Auxiliary configuration Bypass type by opening of contact on terminal block J2 – terminals 4 and 5 0 No auxiliary units Heat pump turned off 1 Electric auxiliary units Only electric auxiliary units turned off 2 Electric auxiliary units Heat pump and electric auxiliary units turned off 3 Boiler auxiliary Heat pump turned off and boiler turned on e.
To access the settings, do as follows: This manual must be read and. Always mix the correct amounts of water, antifreeze and corrosion inhibitor in a container before adding them to the system Procedure 1- Rinse and drain the system Always flush the system completely and blow it out to remove any remaining water.
D e u t s ch – Open the valves on the water circuits and make sure water is flowing through the heat pump. With the unit running, check it thoroughly for any abnormal visual signs or noises. Moreover, a d3 fault water flow rate fault must not prevent caldo boiler from operating. Specifications are subject to change without notice according to Carrier Policy of continuous development.
Electrical connection tightness check Outdoor coil cleaning Control check Differential water pressure switch Status of liquid sight glass and leak detection 44 aquali. AWG 16 to 28; or 0.
If so, the terminal may be located anywhere without affecting control see paragraph under table on page IP 30 – Operating temperature limits: Fault management remains on during test mode.
To do so, loosen the screw Fig. General product information 3.
Bear in mind the weight and dimensions given in this section. The fault type appears on the terminal LCD. LK Aquais Boiler, kw is delivered.