Standards. DIN Manufacturing processes joining – Part 5: Joining by forming processes; Classification, subdivision, terms and definitions. Title ( German). DIN references following documents: DIN , , Manufacturing processes joining – Part 5: Joining by forming processes; Classification. Find the most up-to-date version of DIN at Engineering
|Published (Last):||23 January 2004|
|PDF File Size:||18.84 Mb|
|ePub File Size:||20.15 Mb|
|Price:||Free* [*Free Regsitration Required]|
Air and Exhaust manage The resulting clinched joints are also referred dij as joints in the following. Previous issues VW This electronically generated standard is authentic and valid without signature.
The English translation is believed to be accurate. In case of discrepancies the German version shall govern. No part of this document may be transmitted or reproduced without prior permission of a Standards Department of the Volkswagen Group. Parties to a contract can only obtain this standard via the B2B supplier platform www.
The Structure of the Strength of Riveted Joints Determined in the Lap Joint Tensile Shear Test
Clinching allows for joining of both similar and different materials. It is also possible to join surfacetreated parts zinc-coated, aluminized, organically coated, etc. For details on the assessment of round clinched joints without cutting element, see PV It is the joining of at least two overlapping sheet metal, tube or profile parts achieved by means of cold deformation with punch and die.
The connection is a positive locking and friction locking joint.
Joining by Upset Bulging
Metallic continuity may xin under certain conditions. Considerably lower strength is to be expected if this is not the case. For sheets with different plasticity characteristics, the harder sheet is to be arranged on the side of the punch wherever possible “hard in soft”.
The overall thickness of the joining partners must not exceed 5 mm. There are no generally applicable values for the base thickness tb. The nominal and tolerance values must be determined for each individual case. With segmented dies, the microsections must be located in the center of the die segments. Especially for round joints, care must be taken that the joint does not fall apart when preparing the microsections.
This can be achieved by bonding or by slightly offsetting the microsection location out of the joint center. In the latter case, the microsection must be prepared so that the microsection plane is located in the center of the clinched joint for the determination of the geometric characteristics.
Their properties must match to the cases to be tested. Here, it must be ensured that the measured values are not affected by the preparation work. Specimen width is 45 mm, overlap of the sheets is 35 mm and length of the single sheets is at least mm. Rectangular joints are to be located perpendicular to the load direction. At least 10 specimens are required for the release tests.
The minimum break force Fmin depends on the sheet thickness combination, the strength of the raw material and the type of joint and must be specified in the drawing.
Joining by Upset Bulging | SpringerLink
The result Fmin Ftransverse — 2 sigma is a reference value for the drawing specification. Release testing process qualification A total of 10 specimens according to Section 3. Table 5 — Abbreviations FLS Measured lap-shear force of the individual specimens [kN] Mean value of the measured lap-shear forces [kN] Fmin Minimum value of the lap-shear force according to drawing [kN] As rough values e. Here, at least the ratios specified in Table 6 must be achieved: The flange height is 35 mm Aalternatively 16 mm B.
It must be ensured that the joints are not stressed when the sheets are bent e.
vin The assessment criteria according to Section 3. General information — — Part no. Drawing version desired values of the joint: The joints must be carried out such that window bonding material can be pressed into the recess created by the joining process, see Figure 4.
Page 13 VW In this Section terminological inconsistencies may occur as the original titles are used.
Standards with the titles given in German are either only available in German or may be procured in other languages from the institution issuing the standard. Joining by forming processes; Classification, subdivision, terms and definitions Clinchen -? If the base is cracked, check for microsection preparation errors.
If this is not the case, the joint is NOK. Page 15 VW If undercut is present on both sides: Undercut f not present on both sides: Page 16 VW Page 17 VW If the material flow in the structure is uninterrupted, as can be seen in the Figure on the left, it is a wrinkle.