PC Chips Support > MDLU > Main Support page, PCCWebSite/Products/?. Manuals and free instruction guides. Find the user manual. Manual for MDLU V Motherboard, Motherboard specification for MDLU V user manual PCChips Motherboard Manuals,PC Chips MDLU V.
|Published (Last):||19 January 2013|
|PDF File Size:||17.55 Mb|
|ePub File Size:||11.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may m935ddlu reproduced without the express written consent of the manufacturer.
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability m935dlk fitness for any particular purpose. Further, the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
PC-cillin is a registered trademark of Trend Micro Inc. Other names used in this publication may be trademarks and are acknowledged. I Static Electricity Precautions Take the following precautions when unpacking the mainboard and installing it in a system. Keep the mainboard and other components in their original static-proof packaging until you are ready to install them. During installation, wear a grounded wrist strap if possible. Handle the mainboard carefully by the edges.
Avoid touching the components unless it is absolutely necessary. During installation put the mainboard on top of the static-protection packaging it came in with the component side facing up.
Inspect the mainboard for damage to the components and connectors on the board. If you suspect that the mainboard has been damaged, do not connect power to the system. Contact your mainboard vendor and report the damage. Therefore, it might happen under Windows XP manusl a dialogue box shown as below pop out warning you this software has not passed Windows Logo testing to verify its compatibility with Windows XP.
Please rest assured that our RD department has already tested and verified these drivers. If you connect a USB 2. As soon as the solution is done, the updated USB drive will be released to our website: Unten stehend finden Sie eine Liste mit den Chipsatzteilen und deren jeweiligen Funktionen: Segue una lista con i chipset e le rispettive funzioni: Key Features The key features of this mainboard include: Here is a list of the chipset arrangement and their respective features: You can purchase your own optional accessories m935clu the third party, but please contact your local vendor on any issues of the specification and compatibility.
Identify the mainboard components Install a CPU Install one or more system memory modules Verify that all jumpers or switches are set correctly Install the mainboard in a system chassis case Connect any m935slu brackets or cables to connectors on the mainboard Install any peripheral devices and make the appropriate connections to connectors on the mainboard Note: Before installing this mainboard, make sure jumper JP2 is under Normal setting.
See this chapter for information about locating JP2 and the setting options. Never connect power to the system during installation; otherwise, it may damage the mainboard. Mainboard Components Use the diagram below to identify the major components on the mainboard.
M935DLU motherboard manual – PC Chips M935DLU Motherboard
Any jumpers on your mainboard not appearing in the illustration above are for testing only. Use LPT1 to connect printers or other parallel communications devices. Audio Ports Use the three audio ports to connect audio devices.
The first jack is for stereo Line-In mannual.
The second jack is for stereo LineOut signal. The third jack is for Microphone. When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory. Unhook the locking lever of the CPU socket. Pull the locking lever away from the socket and raising it to the upright position. Match the pin1 corner the beveled edge on the CPU with the pin1 corner on the socket shown as the above illustration.
Insert the CPU into the m935dul. Do not use force. Push the locking lever down and hook it under the latch on the edge of socket. Apply thermal grease to the top of the CPU. Following these steps to install the memory module.
Push down the latches on both sides of the DIMM socket. Align the memory module with the socket. Install the DIMM module into the socket and press it firmly down until it is seated correctly.
The socket latches are levered upwards and latch on to the edges of the DIMM. Install any remaining DIMM modules. You may need to clear the CMOS memory if the settings in the Setup Utility are incorrect and prevent your mainboard from operating.
The board is a Micro ATX size mainboard. You can install this mainboard in an ATX case. Install the mainboard in a case. Follow the instructions provided by the case manufacturer using the hardware and internal mounting points on the chassis. If there is a cooling fan installed in the system chassis, connect the cable from the cooling fan to the CHSFAN fan power connector on the mainboard.
Front Panel Audio Connector This connector allows the user to install auxiliary front-oriented microphone and line-out ports for easier access. Additionally, some computer cases have USB ports at the front of the case.
Locate the JUSB1 connector on m935vlu mainboard. Plug the bracket cable onto the JUSB1 connector. Remove a slot cover from one of the manial slots on the system chassis. Install an extension bracket in the opening.
Secure the extension bracket to the chassis with a screw. You can use a card reader to read or transfer files and digital images to your computer. Make sure the pin assignment will match before plugging in.
Any incorrect usage may m35dlu unexpected damage to the system. Infrared Port The infrared port allows the wireless exchange of information between your computer and similarly equipped devices such as printers, laptops, Personal Digital Assistants PDAsand other computers.
Locate the infrared port IR1 connector on the mainboard. If you are adding an infrared port, connect the ribbon cable from the port to the IR1 connector and then secure the port to an appropriate place in your system chassis.
Drives can be 3. Install your drives and connect power from the system power supply. If you connect two devices to a single cable, you must configure one of the drives as Master and one of the drives as Slave.
Pcchips mdlu v drivers – Google Docs
The documentation of the IDE device will tell you how to configure the device as a Master or Slave device. The Master device connects to nanual end of the cable. If you have two devices on the cable, one must be Master and one must be Slave.
On the mainboard, locate the 4-pin connector CD1. Remove the blanking plate of the slot from the system chassis. Install the edge connector of the expansion card into the slot.
Ensure the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system chassis with a screw. Your computer uses this information to initialize all the components when booting up and functions as the basis for coordination between system components. If the Setup Utility configuration is incorrect, it may cause the system to malfunction. It can even stop your computer from booting properly. You can run the setup utility and manually make changes to the configuration.
You might need to do this to configure some of the hardware that you install on or connect to the mainboard, such as the CPU, system memory, disk drives, etc. When you see this message, press the Delete key and the Main menu page of the Setup Utility appears on your monitor. Select Item Shift F2: Best performance values F You can use the cursor manuwl keys to highlight any of the options on the main menu page. Press Enter to select the highlighted option.
To leave the setup utility, press the Escape key. Some of the options on the main menu page lead to tables of items with installed values. In these pages, use the cursor arrow keys to highlight the items, and then use the PgUp and PgDn keys to cycle through the alternate values for each of the items.
Other options on the main menu page lead to dialog boxes requiring you to answer Yes or No by hitting k935dlu Y or N keys. If you have already made changes to the setup utility, press F10 to save those changes and exit the utility. Press F5 to reset the changes to the original values. Press F6 to m935flu the setup utility with a set of default values.